公共廣播音響設備安裝好后，經過一段時間的使用，總會有一些小的問題需要解決，那么快速排除公共廣播音響擴聲系統故障方法有什么呢？
After the public address sound equipment is installed, after a period of use, there will always be some small problems to be solved. So what are the methods to quickly eliminate the faults of the public address sound reinforcement system?
直觀檢查法
Visual inspection method
直觀檢查法是斷開電源后立即進行。不用儀器、儀表，憑直觀的感覺，調動視覺、聽覺、嗅覺、觸覺等4種感覺特性，進行判斷。這種檢查方法雖然準確性較差些，但速度快，直觀檢查法尤其對電源故障檢查很有用。
Visual inspection is performed immediately after disconnecting the power supply. Without instruments and meters, with intuitive feelings, we can mobilize the four sensory characteristics of vision, hearing, smell and touch to make judgments. Although this inspection method is less accurate, it is fast, and the visual inspection method is especially useful for power failure inspection.
一看:觀察機器或部件及其外部結構。看按鍵開關、接口、指示燈有無松動，線路板接緒有無脫落，有無虛焊、變色、裂痕、爆裂等現象，保險絲有無燒斷、打火、冒煙、變形、未卡住等問題，采用眼睛，直接識別和判斷。
First look: observe the machine or component and its external structure. Check whether the key switch, interface and indicator light are loose, whether the wiring thread of the circuit board falls off, whether there is soldering, discoloration, crack, burst and other phenomena, and whether the fuse is burnt out, ignited, smoking, deformed, not stuck and other problems. Use eyes to directly identify and judge.
二聽:輕輕翻動機器或部件，搖擺搖擺，聽聽有無零件散落或螺絲釘脫落情況，是否有碰擊聲。作連續翻轉有無不正常的“吱吱”聲或“啪啪”的打火聲（通電時）。如果有這些現象，故障可能出現在這些地方。
Second, listen: gently turn the machine or parts, swing, listen to whether there are parts scattered or screws falling off, and whether there is a collision sound. Check whether there is abnormal "squeaking" sound or "popping" fire sound during continuous turnover (when powered on). If there are these phenomena, the fault may appear in these places.
三聞:用鼻子聞聞有無燒焦氣味，找到氣味來源，故障可能出一放出異味的地方。
Three smells: smell with your nose for burning smell, find out the source of the smell, and the fault may be a place that emits peculiar smell.
四摸:用手摸摸變壓器外殼（斷電后進行），不要觸及接線端子，因為有時因充電電容存在，電壓甚高，危及。感覺一下，是否超過正常溫度、發燙，無法觸摸。功率管有無過熱或冰涼現象。調整管有無過熱或冰涼不熱現象。如果有這些現象，問題可能出現在這些地方。
Four touch: touch the transformer shell by hand (after power failure), do not touch the wiring terminal, because sometimes the voltage is very high due to the existence of charging capacitance, which endangers safety. Feel whether it is beyond the normal temperature, hot and untouchable. Check whether the power tube is overheated or cold. Check whether the adjusting tube is overheated or cold. If there are these phenomena, the problems may appear in these places.
試探法
Heuristics
試探法是針對懷疑部分的電路采用比較、分割、替代、模擬等試探手段，尋找
山東公共廣播音響擴聲系統故障所在，然后排除。具體方法如下：
Heuristics is to use comparison, segmentation, substitution, simulation and other heuristics to find the fault of Shandong public broadcasting sound reinforcement system, and then eliminate it. The specific methods are as follows:
1、比較:找一臺與故障機完全相同型號的機器，在設備中利用同一臺機器的左、右聲道部件，測量相對應部分的電壓、電阻、電流數量，再加以比較，找到故障所在。
1. Comparison: find a machine with the same model as the faulty machine, use the left and right channel components of the same machine in professional equipment, measure the voltage, resistance and current of the corresponding parts, and then compare them to find the fault.
2、分割:將某部分電路與其他部分脫開，接上外加電源，注入信號，進行判斷。
2. Division: disconnect a part of the circuit from other parts, connect the external power supply, inject the signal, and judge.
3、替代:用好的元件替代懷疑元件，或?qū)⒆蟆⒂衣暤啦考Q，尤其對于集成電路塊可以這樣進行。如果部件對換之后，機器恢復正常，則說明該部件存在問題或損壞。
3. Replacement: replace the suspected component with a good component, or replace the left and right channel components, especially for integrated circuit blocks. If the machine returns to normal after the parts are replaced, there is a problem or damage to the parts.
4、模擬:溫度模擬，采用電吹風加熱，或用酒精降溫，進行溫度性能檢查，振動模擬是使用細的塑料絕緣棒輕擊某些部件，看看電路工作狀況，可以發現某些虛焊現象，檢查故障所在。這種方法一般由技術熟練者進行，否則，容易出現故障加重現象。
4. Simulation: temperature simulation, using hair dryer heating, or cooling with alcohol, to check the temperature performance. Vibration simulation is to use a thin plastic insulating rod to tap some parts, look at the working condition of the circuit, you can find some false soldering phenomena, and check the fault. This method is generally carried out by skilled people, otherwise, it is easy to aggravate the fault.
以上就是問題解答的相關內容了，希望能夠幫助到大家，如對這一問題還存在任何疑問，都歡迎關注我們網站
http://www.zkvd.cn并咨詢我們的工作人員，將竭誠為您服務。
The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website http://www.zkvd.cn And consult our staff, will serve you wholeheartedly.
魯公網安備 37010202002516號
